E1

Rinse LED - The flood sensor in the base has been activated for more than 20 seconds.

Issue:

Lid not closing Overfilling Foaming Not draining Lid seal damage Dispenser or water softener seals leaking Damaged water inlet or drain hoses Leaking heater plate or motor seals, or drain o-ring seals Yoke jammed or broken Inlet hose to inlet valve connection loose Inlet valve body leak Heater plate damaged (chipped enamel) Dry E1 - PCB mains filter, harness or connectors, electronic controller.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E2

Delicate LED - The controller has not sensed the motor rotating

Issue:

Foreign object has jammed the rotor. The rotor has failed hall sensor or wiring fault at the hall sensor or controller. The hall sensor has failed Motor stator winding or connection open circuit. The electronic controller has failed. PCB mains filter has failed.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E3

Delicate & Rinse LED's - The water temperature has been sensed as greater than 85 °C (185 °F)

Issue:

The incoming water is greater than 85 °C (185 °F). The element has failed closed circuit. The temperature sensor on the heater plate has failed. The electronic controller has failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E4

Fast LED - No temperature increase has been sensed for about 4 hours while element is on.

Issue:

The element is not connected. The element is failed open circuit. The temperature sensor has failed. The electronic controller has failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E5

Fast & Rinse LED's - Lid motor current too high during start

Issue:

The lid is jammed up or down. The electronic controller has failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E6

Fast &Delicate LED's - Fan fault

Issue:

Check fan harness connector. Check if fan open or short circuit. The electronic controller has failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E7

Fast, Delicate & Rinse LED's - Detergent diverter fault

Issue:

Check harness connections. Coil is open circuit. Coil is short circuit. The electronic controller has failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E8

Normal LED - Solenoid fault

Issue:

Check the harness connections at each solenoid. Coil is open circuit. Coil is short circuit

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E9

Normal & Rinse LED - Microcontroller fault

Issue:

Badge isolator (if present). Detergent diverter valve. Check harness connections. MFB. Controller

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

EC

Normal & Fast LED's - Communications error

Issue:

Harness connections between the MFB and controller. MFB. Faulty top controller. Faulty bottom controller

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U1

Heavy & Rinse LED's - Water Supply

Issue:

Water turned off. Insufficient water supply pressure. Blocked water softener filter (if fitted). Spilt rinse aid casuing over foam in tub. Incorrect detergent being used. Motor rotor. The machine is siphoning. Inlet valve has failed. Controller

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U4

Heavy & Fast LED's - Other tub is faulting

Issue:

The other tub has a fault which is preventing operation of that tub. No repair is required to the tub showing a U4.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U6

Heavy, Fast & Delicate LED's - Spray arm not detected

Issue:

Spray arm not sitting on rotor. Insufficent water pressure

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U1

No water

Issue:

No water - the water supply hasn't been turned on.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U4

Fault in the other drawer preventing the use of this drawer.

Issue:

Fault in the other drawer preventing the use of this drawer.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U6

The spray arm has loosened or come off its mounting

Issue:

The spray arm has loosened or come off its mounting, or water pressure is too low.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E1

Flood detected.

Issue:

Flood detected.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E2

Motor fault.

Issue:

Motor fault.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E3

Temperature sensor fault.

Issue:

Temperature sensor fault. You may need to have a tempering valve installed on your water supply, to ensure that incoming water is less than 65°C (149°F).

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E4

Heating element failed.

Issue:

Heating element failed.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E5

Fault with the internal lid of the dishwasher.

Issue:

Fault with the internal lid of the dishwasher.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E6

Fault with the drying fan.

Issue:

Fault with the drying fan.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E7

Electronics fault

Issue:

Electronics fault — detergent dispensing system.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E8

Electronics fault

Issue:

Electronics fault — other systems.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E9

Electronics fault

Issue:

Electronics fault — controller.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

EC

Electronics fault

Issue:

Electronics fault — communication between drawers.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U1

Heavy; Rinse - No water

Issue:

No water - the water supply hasn't been turned on.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U4

Heavy; Fast - Fault in the drawer

Issue:

Fault in the other drawer preventing the use of this drawer.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

U6

Heavy; Fast; Delicate - The spray arm has loosened or come off its mounting

Issue:

The spray arm has loosened or come off its mounting, or water pressure is too low.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E1

Rinse - Flood detected

Issue:

Flood detected

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E2

Delicate - Motor fault

Issue:

Motor fault

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E3

Delicate; Rinse - Temperature sensor fault

Issue:

Temperature sensor fault. You may need to have a tempering valve installed on your water supply, to ensure that incoming water is less than 65°C (149°F).

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E4

Fast - Heating element failed

Issue:

Heating element failed

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E5

Fast; Rinse - Fault with the internal lid of the dishwasher

Issue:

Fault with the internal lid of the dishwasher

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E6

Fast; Delicate - Fault with the drying fan

Issue:

Fault with the drying fan

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E7

Fast; Delicate; Rinse - Electronics fault

Issue:

Electronics fault — detergent dispensing system.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E8

Normal - Electronics fault

Issue:

Electronics fault — other systems.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

E9

Normal; Rinse - Electronics fault

Issue:

Electronics fault — controller.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

EC

Normal; Fast - Electronics fault

Issue:

Electronics fault — communication between drawers.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Fisher & Paykel Dishwasher Repairs in London.

Е2

No water (inlet hose closed).

Issue:

No water (inlet hose closed).

Advice:

Turn off the dishwasher, open the inlet hose and reset the cycle. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E3

The machine cannot drain water.

Issue:

The machine cannot drain water.

Advice:

Check if the drain tube is bent or if the siphon or filters are clogged. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E4

Water leak

Issue:

Water leak

Advice:

Check if the drain tube is bent or if the siphon or filters are clogged. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E5

Electronic temperature control fault.

Issue:

Electronic temperature control fault.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London.

E6

Electronic control fault.

Issue:

Electronic control fault.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London.

E8

The water heating element is not working correctly or the filter plate is clogged.

Issue:

The water heating element is not working correctly or the filter plate is clogged.

Advice:

Clean the filter plate. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E1

Water fill time out.

Issue:

The dishwasher has failed to fill with water in a reasonable time

Advice:

Check water supply. Check water inlet valve. Check wiring to water inlet valve. Check connections to water inlet valve. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E2

Water drain time out.

Issue:

The dishwasher has failed to drain the water in a reasonable time.

Advice:

Check water drain or waste hose. Check plumbing at drain point. Check water drain pump. Check wiring to water drain pump. Check connections to water drain pump. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E3

Water heating time out or fault.

Issue:

The dishwasher has failed to heat with water in a reasonable time or has failed to detect the water heating element.

Advice:

Check water heating element wiring. Check water heating element. Check wiring to main control module. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E4

Anti flood device tripped.

Issue:

The dishwasher has detected a water leak through the anti flood device being activated.

Advice:

Check base of the dishwasher for any leaks. Check resolve any leaking components. Check wiring to anti flood device. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E6

NTC open circuit detected.

Issue:

The dishwasher has detected an open circuit error with the temperature sensor or NTC.

Advice:

Check wiring to temperature sensor. Check temperature sensor. Check wiring control module. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E7

NTC shorted error.

Issue:

The dishwasher has detected an short circuit error with the temperature sensor or NTC.

Advice:

Check wiring to temperature sensor. Check temperature sensor. Check wiring control module. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Candy Dishwasher Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

IE

Water inlet error - washing machine failed to fill

Issue:

The fault code is displayed, if the washing machine does not detect any incoming water.

Advice:

• Check wiring to water inlet valve
• Check water valve
• Check drain pump
• Check pressure switch
• Check PCB

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

OE

Water has failed to drain from the washing machine

Issue:

This faut code is displayed should the washin gmachine or washer dryer fail to drain water from the tank.

Advice:

• Check drain pump
• Check wiring
• Check water level sensor
• Check connections to water valve and PCB

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

UE

Wash load imbalance detected

Issue:

The wash load has been detected as an unbalanced load and the washing machine or washer dryer has failed to spin.

Advice:

• Sort the laundry load and attempt spin again

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

LE

Washing machine door opening error

Issue:

The washing machine or washer dryer door has been detected as open or unlocked.

Advice:

• Close the door!
• Check the door lock switch
• Check the door latch
• Check PCB

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E2O

verfilling error

Issue:

The washing machine has detected an overfill situation and the failure code is displayed.

Advice:

• Check water inlet valve
• Check drain pump
• Check pressure switch or level sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E3

Fan motor error detected

Issue:

On washer dryer mdels an error has been detected with the dryer fan motor.

Advice:

• Check fan motor for obstruction or blockage
• Check fan motor continuity
• Check PCB

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E9

Pressure sensor error

Issue:

The washing machine has detected an error with the pressure switch or level sensor

Advice:

• Check wiring to level sensor
• Check level sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E5

High voltage error

Issue:

We're not quite sure what this one means as the fault code sheet says the following causes this error:

• Huge noise (don't ask us??)
• Spinning with clothing jammed between the drum and gasket
• PCB failure

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London.

E6

EMG Error

Issue:

Again, your guess is as good as ours on this one as well with the following being listed against the error

Advice:

• Huge noise (don't ask us??)
• Spinning with clothing jammed between the drum and gasket
• Motor failure
• PCB failure

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E7

Direction error

Issue:

This error code is displayed should the motor or drum be detected in moving in the opposite direction it should.

Advice:

• Check hall sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E8

Washing machine motor error detected

Issue:

A fault has been detected with the main drive motor.

Advice:

• Check motor connection block
• Abnormal loading condition

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H1

Dryer temperature sensor error detected

Issue:

A fault has been detected with the dryer temperature sensor on washer dryer models.

Advice:

• Check connections to dryer sensor
• Check temperature sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H2

Wash temperature sensor error detected

Issue:

A fault has been detected with the washing thermistor or temperature sensor.

Advice:

• Check connections to wash temperature sensor
• Check temperature sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H3

Overheating dryer heater element detected

Issue:

A fault has been detected with the dryer side heating.

Advice:

• Check fan motor is clear and unobstructed
• Check wiring
• Check dryer heating sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H4

Overheating wash heating element detected

Issue:

A fault has been detected were the washing machine is overheating on wash.

Advice:

• Check water level
• Check temperature sensor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H6

Wash heating element failure detected

Issue:

A fault has been detected were the element is not heating.

Advice:

• Check wash heating element
• Check wiring
• Check thermistor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H7

Dryer heating element failure detected

Issue:

A fault has been detected with the drying heater element.

Advice:

• Check wiring
• Check dryer heater element
• Check wiring
• Check thermistor

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

H8

Washing heater overheating detected - no water in washing machine

Issue:

The wash heating element has been detected as working with no water in the washing machine.

Advice:

• Check water level
• Check wiring
• Check thermistor
• Check PCB

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

PEF

Washing machine filter detected as blocked

Issue:

The machine has detected the drain filter as being blocked

Advice:

• Check the drain filter and clear any blockage

If the fault persists, please arrange an engineer visit. We offer fixed price Daewoo Washer Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E1

Dishwasher water intake has timed out

Issue:

If the water inlet valve has worked for 4 mins and the flowmeter detects that not enough water has entered the Dishwasher (3.5l) the the control board will shut down all functions and the alarm buzzer will sound for 30 secs and E1 will be displayed on the control panel, the Dishwasher will pause for 3 mins and then drain out the water for 90 secs and revert to the rest position.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Belling Dishwasher Repairs in London.

E3

Dishwasher heating element operating when it should not

Issue:

If the heating element is still heating after the allowed time, then the control board will advance the programme to next step and at the end of the washing cycle the alarm buzzer will sound for 30 sec and the display will show E3. When the contol board detects that the heating element is operating during a non heating step or during the internal test the heating circuit is found to be open circuit then the alarm buzzer will sound for 30 sec and the control board will cease all functions except for the drain cycle which will run for 90 seconds and then E3 will be displayed on the contol panel.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Belling Dishwasher Repairs in London.

E4

Dishwasher has overfill or leak detected

Issue:

Any time that the float chamber micro switch operates for more than 2 secs the control board will shut down all functions and operate the drain pump for 30 secs and then sound the alarm buzzer for 30 secs and the control panel displays E4. If the microswitch sets during the draining period then the control board will allow the dishwasher to function normally again, or the dishwasher will then revert to constant draining until the micro switch returns to normal rest position.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Belling Dishwasher Repairs in London.

E6

Dishwasher has detected the temperature thermistor as open circuit

Issue:

If after the control board has carried out an internal test and found the thermister open circuit the dishwasher will cease all functions and the alarm buzzer will sound for 30 secs and the control panel will display E6 after a further 3 mins the machine will operate the drain pump for 90 secs and revert to rest position.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Belling Dishwasher Repairs in London.

E7

Dishwasher has detected the temperature thermistor as shorted

Issue:

If after the control board has carried out an internal test and found the thermister short circuit the dishwasher will cease all functions and the alarm buzzer will sound for 30 secs and the control panel will display E7 atfer a further 3 mins the machine will operate the drain pump for 90 secs and revert to the rest position.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Belling Dishwasher Repairs in London.

tE

Defective thermistor (temperature sensor)

Issue:

Clean the lint filter because a clogged lint filter can cause this code. Check the exhaust vent system for a clog or restriction and clean system if blocked. If the lint filter and exhaust vent system are clear, unplug the dryer and check the wire harness connections between the thermistor and the electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, measure the thermistor resistance using a multimeter. You should measure around 10,000 ohms of resistance at room temperature. Replace the thermistor if resistance is off. If thermistor resistance is okay and the wire harness is intact, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

dE or dF

Door switch is defective

Issue:

If you're attempting to start the dryer with the door open, close the door. If the door is closed when the code appears, unplug the dryer and check the wire harness connections between the door switch and the electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness is okay, replace the door switch.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

dF

Door switch failure

Issue:

Unplug the dryer and check the wire harness connections between the door switch and the electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness is okay, replace the door switch.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

bE2

Stuck button on the control panel

Issue:

Press all the buttons on the control panel to free the stuck button. If the stuck button can't be freed, replace the user interface control.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

FE

Power supply frequency is out of range

Issue:

Have an electrician or your electrical power supplier check the frequency of your electrical power supply. If the dryer is getting the 60 Hz power it requires, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

9E1

Electronic control board error (over voltage)

Issue:

Unplug the dryer for 5 minutes to reset the control board. If the code returns after you restore power to the dryer, check the voltage supply. If the voltage supply is between 105 and 130 VAC, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

AE

Electronic control board error (communication problem)

Issue:

Unplug the dryer and check the wire harness connections on the electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

EEE

Control board failure

Issue:

Unplug the dryer for 5 minutes to reset the control board. If the code returns after you restore power to the dryer, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

HE

Heating error (gas and electric dryers)

Issue:

For gas dryers, make sure the gas supply cut-off valve for the dryer is fully open. If it's an electric dryer, see if a house circuit breaker for the dryer is tripped; the dryer won’t heat if a leg of the 240-volt power supply is off. Unplug the dryer and check the wire harness connections between the electronic control board and the heater. Reconnect any loose wires or replace the wire harness if damaged. For an electric dryer, check the heating element for damage and replace if broken. For a gas dryer, have a technician check and repair the heating system.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

tS

Thermistor (temperature sensor) is defective (electrically shorted)

Issue:

Unplug the dryer and use a volt/ohm meter to test the resistance of the thermistor. If the resistance is more than 40,000 ohms, replace the thermistor. If the resistance is 10,000 ohms, replace the wire harness, if damaged. If the wire harness is okay, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

tO

Thermistor is defective (electrically open)

Issue:

Unplug the dryer and use a volt/ohm meter to check the resistance of the thermistor. The thermistor should measure around 10K ohms (10,000 ohms) of resistance at room temperature (77 degrees). If the resistance of the thermistor is higher than 40K ohms, replace it. If the resistance of the thermistor is normal, check the wire harness and replace the wire harness if damaged. If the wire harness is okay, replace the electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

do

Door is open

Issue:

Unplug the dryer and check for loose or damaged wiring connections in the door switch circuit. Reconnect the wire harness if loose or disconnected. Replace the wire harness if damaged. Replace the door switch if damaged or defective.

Advice:

When this flashes, the repair can be as simple as closing the dryer door firmly. But, the door may need a bit more attention to function properly. Begin by cleaning the door switch/lock to remove any lint or residue that is keeping it from closing properly. Use a bit of rubbing alcohol on a cotton swab to clean the connectors. If that doesn't work: Unplug the dryer and check for loose or damaged wire connections in the door lock/switch circuit. Reconnect the wires if loose or disconnected or replace the wire harness if damaged. If the door switch is damaged, it should be replaced.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

FE

Power supply frequency is out of range

Issue:

Have an electrician or your electrical power supplier check the frequency of your electrical power supply. If the dryer is getting the 60 Hz power it requires, replace the electronic control board.

Advice:

You can test the voltage of the dryer with a voltage meter. If the dryer is getting the 60 Hz power it requires, the electronic control board is faulty and must be replaced. This requires an engineer. An engineer should check the frequency of your electrical power supply when they come for the repair appointment.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

dF

Door circuit failure

Issue:

Unplug the dryer and check for loose or damaged wiring connections in the door switch circuit. Reconnect the wire harness if loose or disconnected. Replace the wire harness if damaged. Replace the door switch if damaged or defective.

Advice:

This code is similar to door open but will definitely need a bit more investigation. Unplug the dryer and check for loose or damaged wiring connections in the door/lock switch circuit. Reconnect the wires or replace the wires if they look burned or damaged. It may be necessary to replace the entire door lock/switch.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

HE or hE

Heating error (gas dryer)

Issue:

Make sure the gas supply cut-off valve for the dryer is fully open. Unplug the dryer and reconnect any loose wiring connections on the gas valve coils. Replace the wire harness if damaged. Have a service technician check the heating system.

Advice:

Begin by checking that the gas supply cut-off valve for the dryer is fully open. Unplug the dryer and reconnect any loose wiring connections on the gas valve coils or replace the wire harness if damaged. If that doesn't solve the issue, have a service technician check the gas heating system.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

HE or hE

Heating error (electric dryer)

Issue:

See if a house circuit breaker for the dryer is tripped; the dryer won’t heat if a leg of the 240-volt power supply is off. Unplug the dryer and check the wiring connections on the heating element. Reconnect any loose wires and replace the wire harness if damaged. Check the heating element for damage and replace the heating element if defective.

Advice:

First, check the circuit breakers in your home's electrical box to see if they have tripped. Reset if they have tripped. Next, unplug the dryer and check the wiring connections on the heating element. Reconnect any loose wires or replace the wire harness if damaged. Check the heating element for damage and replace the heating element if it appears defective.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

bE

Stuck button on the control panel

Issue:

Press all the buttons on the control panel to free the stuck button. If the stuck button cannot be freed, replace the user interface control.

Advice:

Press all the buttons on the control panel to free the stuck button. If the stuck button cannot be freed, replace the user interface control.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

Od

Excessive dry time

Issue:

Unplug the dryer and inspect the moisture sensor bar wiring connections. Reconnect any loose wires. Replace the wire harness if damaged. Replace the moisture sensor bar if damaged.

Advice:

First, empty the lint filter. Clean the moisture sensor inside the dryer drum with a bit of rubbing alcohol and a cotton swab. If you use dryer sheets, they coat the sensor with residue and extend drying time by tricking the sensor. Take time to be sure that dryer ducts and vents are open and clog free. Excess lint impedes the air flow and makes dryer hard. Finally, unplug the dryer and inspect the moisture sensor bar wiring connections. Reconnect any loose wires and replace the wiring or sensor bar if damaged.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

Et

Control board failure

Issue:

Unplug the dryer for 5 minutes to reset the control board. If the code returns after you restore power to the dryer, replace the electronic control board.

Advice:

First, unplug the dryer for five minutes to reset the control board. If the code returns after you restore power to the dryer, the electronic control board will need to be replaced.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Samsung Tumble Dryer Repairs in London.

E1

Door is open

Issue:

Close the dryer door if open. If the door is closed when the code is displayed, unplug the dryer and reconnect the wire harness on the door switch. Replace the wire harness if damaged. If the wire harness is okay, replace the door switch.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Haier Tumble Dryer Repairs in London.

E2

Not heating

Issue:

If the dryer actually doesn’t heat, unplug the dryer and replace any defective heating system components. If the dryer does heat, measure the temperature sensor resistance using a volt/ohm meter. If the resistance isn't 10K ohms at 72 degrees F, replace the temperature sensor.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Haier Tumble Dryer Repairs in London.

E3

Load is wet at end of cycle

Issue:

If the dryer doesn’t heat, unplug the dryer and replace any defective heating system components. If the dryer heats, clean the lint screen because decreased air flow due to a clogged lint screen prevents the load from drying. Clear the exhaust vent duct system of clogs.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Haier Tumble Dryer Repairs in London.

E5

Temperature sensor is defective

Issue:

Unplug the dryer and measure the temperature sensor resistance using a volt/ohm meter. If the resistance isn't 10K ohms at 72 degrees F, replace the temperature sensor.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Haier Tumble Dryer Repairs in London.

EH1, EH2 or EH3

Voltage supply problem

Issue:

Unplug the dryer and measure the voltage supply at the wall outlet using a multimeter. If the voltage isn't between 208 and 240 VAC, have an electrician repair the problem.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex21 or Ex22

Condensate drain pump failure

Issue:

Unplug the dryer and check the wire harness between the condensate drain pump and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, check the pump and drain hose for a clog or restriction. If the drain path is clear, replace the condensate drain pump. If the problem continues, replace the main electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex31 or Ex32

Humidity sensor failure

Issue:

Unplug the dryer and check the wire harness between the humidity sensor and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. Check the humidity sensor and replace it if damaged. If the wire harness connections and humidity sensor are okay, replace the main electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex45

Door open

Issue:

The main electronic control board detects whether the door is open. Close the door if it’s open. If the door is closed, unplug the dryer and check the wire harness between the door switch and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the door switch. If the problem continues, replace the main electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex51

Drive motor failure

Issue:

Unplug the dryer and check the wire harness connections between the main electronic control board and the drive motor. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the main electronic control board. If the problem continues, replace the drive motor.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex52

Drive motor thermal cut-out tripped

Issue:

The thermal cutout trips when the drive motor overheats. Overloading the dryer can cause the motor to overheat. Remove some of the load if too large or heavy. Allow the motor time to cool off and restart the dryer. If the dryer isn’t overloaded, unplug the dryer and remove the load. Spin the drum by hand to check for drive system friction. If you detect excessive friction, check all drive components and replace any damaged parts.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

EX53

Motor sensing circuit error

Issue:

The main electronic control board detects an internal error in its motor circuit. Unplug the dryer and replace the main control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex54

Jammed drive motor

Issue:

Overloading can prevent the motor from running. Remove some of the load if too large or heavy. If the dryer isn’t overloaded, unplug it and remove the load. Spin the drum by hand to check for drive system friction. If you detect excessive friction, check all drive components and replace any damaged parts.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E57 or E58

Inverter board is drawing excessive current

Issue:

The inverter board supplies run voltage to the drive motor. Unplug the dryer and check the wire harness connections between the inverter board and the drive motor. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the drive motor.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E59

No drive motor tachometer signal

Issue:

The inverter board supplies run voltage to the drive motor. Unplug the dryer and check the wire harness connections between the inverter board and the drive motor. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the drive motor because the tachometer is a component of the drive motor and isn't available as a separate part.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E5A

Overheated inverter board

Issue:

This error can be caused by continuous dryer operation in hot ambient conditions. Allow the dryer to cool and then try to restart the dryer. If the code appears under normal operation and conditions, unplug the dryer and replace the inverter board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E5H

Motor voltage is too low (below 100 volts)

Issue:

Unplug the dryer and check the wire harness connections between the drive motor and inverter board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the inverter board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E5C

Voltage supply is too high (above 240 volts)

Issue:

Unplug the dryer and check the voltage supply using a multimeter. Supply voltage shouldn't exceed 240 volts. Contact your electric company is supply voltage is too high. If supply voltage is okay, you’ll usually need to replace the inverter board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E5d or E5E

Communication error between the inverter board and the main electronic control board

Issue:

Unplug the dryer and check the wire harness connections between the main electronic control board and the inverter board. Reconnect any loose wires or replace the wire harness if damaged. A faulty line filter can also cause this error code. The line filter eliminates interference from the power supply. Check the wire harness connections between the line filter and the main electronic control board. If all wiring connections are okay, you may need to replace the line filter, main electronic control board or the inverter board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

E5F

Inverter board failed to start the drive motor

Issue:

Unplug the dryer and check the wire harness connections between main control board and the inverter board.

Advice:

Reconnect any loose wires and replace the wire harness if damaged. If the wire connections are okay, replace the inverter board. If the problem continues, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex62

Shorted compressor

Issue:

Unplug the dryer and check the wire harness connections between the main control board and compressor.

Advice:

Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, you'll probably need to have the compressor replaced. A service technician should do this repair because it involves recovering and recharging refrigerant in the sealed refrigerant system.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex63

Compressor not operating

Issue:

Unplug the dryer and check the wire harness connections between the main control board and compressor.

Advice:

Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, you'll probably need to have the compressor replaced. A service technician should do this repair because it involves recovering and recharging refrigerant in the sealed refrigerant system.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex64

Compressor sensor circuit failure

Issue:

Unplug the dryer and check the wire harness connections between the main control board and compressor.

Advice:

Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, you'll probably need to replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex71

Temperature sensor failure

Issue:

Unplug the dryer and measure the resistance of the temperature sensor using a multimeter. You should measure about 5,000 ohms of resistance at 77 degrees. If not then replace the temperature sensor because it's defective. If resistance is okay, check the wire harness connections between the temperature sensor and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay then you'll usually need to replace the main electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex83, Ex86 or Ex87

Main control board failure

Issue:

Unplug the dryer and replace the main electronic control board.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex91

User interface communication failure

Issue:

Unplug the dryer and check the wire harness connections between the user interface and main electronic control board.

Advice:

Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, replace the user interface board. If the problem continues, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex92 or Ex98

User interface is incompatible with the main electronic control board

Issue:

This code appears when you replace the user interface or the main electronic control board using the wrong part.

Advice:

Use your dryer model number to check the part number and install the compatible part.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

Ex9E

One or more user interface buttons don't work

Issue:

Unplug the dryer and check the wire harness connections between the user interface and the main electronic control board.

Advice:

Reconnect any loose wires or replace the wire harness if defective. If the wire harness connections are okay, replace the user interface.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

ExH1

Incoming power supply frequency out of limits

Issue:

Unplug the dryer. Have your local electrical power service provider check the power supply frequency.

Advice:

If it's normal and the code doesn't clear, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

ExH2

Power supply voltage too high (above 130 VAC)

Issue:

Unplug the dryer and check the outlet voltage using a multimeter.

Advice:

If the voltage is high, have an electrician repair the voltage supply problem. If the voltage is normal, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

ExH3

Power supply voltage too low (below 100 VAC)

Issue:

Unplug the dryer and check the outlet voltage using a multimeter.

Advice:

If the voltage is low, have an electrician repair the voltage supply problem. If the voltage is normal, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.

ExH4, ExHD, ExHE, ExHF, ExF6

Main electronic control board failure

Issue:

Unplug the dryer and check the wire harness connections between the main electronic control board and the user interface.

Advice:

Reconnect any loose wires or replace the wire harness if damaged. If the wire harness connections are okay, replace the main electronic control board.
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price Electrolux Tumble Dryer Repairs in London.