Monday - Friday: 09:00 - 18:00, Saturday: 09:00 - 17:00

Kitchen Appliance Fault Codes

Fault codes or error codes for appliances including washing machines, washer dryers, cookers, dishwashers and fridges.

Error codes for AEG Tumble dryer

  • Product Types: Tumble Dryer

Please do take care to read the information thoroughly as it is there to help you understand fault codes and to keep you safe. There are also some help, tips and hints with a lot of the fault codes published here that you usually will not find anywhere else and, as we learn, we add more information so if you can't find what you need please ask in the forums.

Before using this section please understand that fault or error codes are used as a diagnostic aid, they are not a replacement for diagnostic skill on the part of the person repairing the product and are not in any way usually going to point to the precise component that is faulty. All they do is give you an idea of where to start looking for the fault.

AEG Tumble dryer Error codes

These error code explanations can help you diagnose a problem with your AEG Tumble dryer.

E50

My Dryer shows the error code E50

Issue:
The error E50 is related to a motor or a software problem.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E60

Now the Dryer turns off at ventilate and shows error-code E60 and stays cold

Issue:
The error E60 is related to a heating problem. This problem can be caused by insufficient ventilation in the room.
Advice:
Ensure that there is sufficient fresh air in the room is, and that the device is not built in. This problem can also be caused by a dirty condenser or dirty fluff filters. Ensure that they are clean. If the error code still appears, then the problem can be solved by a service engineer. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E20

There is the error message "E20" in the display of my dryer.

Issue:
E20 (or 2 beeps as an acoustic alarm in some models) indicates a water drainage or pump problem.
Advice:
Please check correct installation to external drainage if applicable. You can connect an external water hose to a condensation dryer with a water reservoir at the top, to drain the water away straight in the drain. There is a red hose at the top on the rear of the tumble dryer. This hose needs to be disconnected at the top and extended to hang in the drain. The water then no longer gets in the water reservoir but runs straight off via the drain. Please check that the hose does not have any kinks or blockages in it. Try to avoid any loops in the hose, shorten the length of the hose so the nozzle is at bottom of the appliance, otherwise, leakage can occur. If the fault persists, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

Dryer is not starting and the start-/pause-key is blinking.

Issue:
The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

The Start - Pause LED is flashing at my dryer.

Issue:
The Start - Paude LED indicates the End of a selected program. At the End of a Dryer program first all LED's will illuminate. This indicates the anti-crease phase (30 min.); Afterwards the Start - Pause will turn Off and Filter-, Condensor- and End- LED's will illuminate (10 min.); Finally all LED's will turn Off and the Start - Pause starts flashing.
Advice:
This is normal, no remedy required.

ERR

The error message "ERR" flashes 2 times in the display of my dryer (Iron Aid).

Issue:
Fill the steam reservoir to MAX. If the icons are still it up, there is a problem and this has to be checked and repaired by a Service Engineer.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E50

There is the error message "E50" in the display of my dryer.

Issue:
There is a problem with the motor or a software problem.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

C0

There is the error message "C0" in the display of my Dryer.

Issue:
There is no problem with the appliance.
Advice:
This is normal, no remedy required.

E20

My Dryer shows the error-code E20

Issue:
The error E20 is related to a draining or a software problem.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E40

My Dryer shows the error-code E40

Issue:
If an error message E40 appears on the display of your dryer, maybe you forgot to close the door of your dryer, after pressing the start button. If the door is closed and the error message still appears it could be a software problem.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E60

There is the error message "E60" in the display of my dryer.

Issue:
It’s possible that the programme has been interrupted and the system needs time to cool down. Try again after 30 min.
Advice:
If the fault persists, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

The condenser LED is lit at my dryer.

Issue:
This is an indication that the condenser has to be cleaned regularly. If the appliance does not dry properly, clean the condenser, filters and air channels.
Advice:
If cleaning does not help, this has to be checked and repaired by a Service Engineer. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

The reservoir LED is lit or flashing at my dryer.

Issue:
The water reservoir LED is always lit at the end of the drying programme, to remind you to empty the water reservoir after every drying cycle. It is normal if the water reservoir LED is lit after the first drying cycle and there is no water in the water reservoir. The water is first collected in a big reservoir before it is drained off to the water reservoir. If the LED is still lit after switching the appliance off and back on again, or if it lights up early on in the programme, there is water in the overflow reservoir. It’s possible that the condenser has to be cleaned (see user manual). If the tumble dryer is connected to the drain via a hose, it has possibly not been done properly if there is a loop in the hose or if the drainage hose has not been shortened.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

C2

My Dryer shows the error-code C2

Issue:
The error C2 is related to a draining or a software problem.
Advice:
Before booking an engineer it is recommended to reset your appliance. Reset can be done by unplugging the appliance from the socket, wait 30 seconds and plug it back again. If you do not have access to the socket, you may also achieve the same result via the circuit breaker of your home. After plugging in the appliance to the socket, start the appliance and select a programme. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

I cannot turn off the warning light(s) on my Dryer

Issue:
Most of the dryers have three warning LEDs on the control panel. The filter LED: This LED is always lit at the end of the drying programme, to remind you that the filter has to be cleaned after every drying cycle. The indication disappears when the appliance is switched off and back on again. The water reservoir LED (only for condenser and heat pump dryers): This LED is always lit at the end of the drying programme, to remind you to empty the water reservoir after every drying cycle. It is normal if the water reservoir LED is lit after the first drying cycle and there is no water in the water reservoir. The water is first collected in a big reservoir before it is drained off to the water reservoir. If the LED is still lit after switching the appliance off and back on again, or if it lights up early on in the programme, there is water in the overflow reservoir. It’s possible that the condenser has to be cleaned.If the dryer is connected to the drain via a hose, it has possibly not been done properly if there is a loop in the hose or if the drainage hose has not been shortened. The condenser LED (only for condenser and heat pump dryers): This LED is an indication that the condenser has to be cleaned regularly. If the appliance does not dry properly, clean the condenser, filters and air channels.
Advice:
The indication disappears when the appliance is switched off and back on again. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

My Dryer is making an alarm noise

Issue:
The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

There is a LED lit or a LED flashing on my Dryer

Issue:
The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

C6

There is the error message "C6" in the display of my Dryer.

Issue:
There is a problem with the moisture sensor. The programme has taken longer than normal, longer than 4.5 hours. Check that the appliance is connected to a mains socket with safety earth.
Advice:
If this is not the case, there is a problem with the moisture measurement and this can be resolved by a Service Engineer. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

C7

There is the error message "C7" in the display of my Dryer.

Issue:
Reaching the right temperature takes too long. It’s possible there is a problem with the heating element.
Advice:
Check that the filters and the condenser (if applicable) are clean. If the fault persists, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

C8

There is the error message "C8" in the display of my Dryer.

Issue:
There is a problem with the temperature sensor.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

CD

There is the error message "CD" in the display of my dryer.

Issue:
There is a problem with the door lock.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

CE, CF

There is the error message "CE" or "CF" in the display of my dryer.

Issue:
There is a problem with the electronics.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

There a padlock shown in the display of my dryer.

Issue:
The child safety lock has been activated This means the programme cannot be started or (unintentionally) changed. De-activation varies per appliance, so please consult the user manual of your model for details.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

The filter LED is lit at my dryer.

Issue:
The filter LED is always lit at the end of the drying programme, to remind you that the filter has to be cleaned after every drying cycle.
Advice:
The indication disappears when the appliance is switched off and back on again. If the problem persists, please arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E21

Canister fill pump triac faulty.

Issue:
Wiring faulty; Electronic board faulty. Cycle interrupted. OFF
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E22

Triac “sensing” circuit for the canister fill pump faulty

Issue:
Electronic board faulty. Cycle interrupted.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E51

Motor power triac short-circuited.

Issue:
Motor faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Cycle interrupted.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E52

Intervention of motor overheating safety cut-out.

Issue:
Motor faulty; Intervention of motor overheating cutout; Wiring faulty; Electronic board faulty. Machine Status/Action: Power to the heater unit and reversal of the direction of rotation are interrupted. If the problem does not re-occur, the alarm is memorised and the cycle continues. If the fault persists after several attempts to supply power (about 35 min.), alarm E51 is generated.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E53

Motor triac “sensing” circuit faulty.

Issue:
Electronic board faulty. Machine Status/Action Cycle interrupted.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E54

Motor in-operational.

Issue:
Excessive wash load; Voltage too low; Motor/transmission system inoperative. Machine Status/Action: Cycle paused after several attempts at powering the motor.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E61

Insufficient heating (maximum time exceeded).

Issue:
Heater unit faulty; Wiring faulty; NTC sensor incorrectly calibrated/out of position; Electronic board faulty. Machine Status/Action: Cycle paused.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E62

Power relay to heater unit faulty.

Issue:
Heater unit faulty; Wiring faulty; Electronic board faulty. Machine Status/Action: Forced cooling cycle.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E63

Intervention of auto-reset thermostat on the heater unit.

Issue:
Thermostat faulty (replace heater unit); Heater unit faulty; Wiring faulty; Electronic board faulty. Machine Status/Action: Disconnects the power supply to the heater unit. If the problem does not re-occur, the alarm is memorised and the cycle continues. If, after several attempts to restore power, the fault persists, alarm E62 is generated.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E64

Heater thermostat.

Issue:
Heater thermostat faulty: Wiring faulty; Electronic board faulty.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E65

Fan motor triac faulty.

Issue:
Fan motor wiring not connected; Motor faulty; Triac interrupted.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E66

Fan motor thermal protection.

Issue:
Fan motor wiring not connected; Motor faulty; Triac interrupted.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

E67

Triac control faulty.

Issue:
Fan motor wiring not connected; CRM board faulty.
Advice:
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Tumble Dryer Repairs in London.

Arrange a visit from a Dishwasher engineer

If you do need an engineer to visit your home, help is at hand. We’ll arrange for an engineer near you to call in and fix your appliance, at a time that’s suitable for you.

Book online or give us a call on 0208 226 3633

London Only - Coverage Area | ( Monday - Friday: 8:00 - 20:00 / Saturday: 09:00 - 18:00 )

Warning! To avoid personal injury or death, always unplug the appliance or disconnect the power before attempting any repairs. Always turn off the gas at the source before repairing any gas appliance. Always wear safety glasses when using tools. Keep loose clothing and hair away from any moving parts. Safety is of major importance when performing any service or repair on any electrical appliance. Please, read our disclaimer before proceeding.

Read 161990 times

Ask a Question

Book Online

Arrange an engineer visit online (London only)

Book a Repair

Quick Question

Captcha

My Account

Remember Me

Register for an online account and you'll be able to:

  • Log in at any time 24/7
  • Book an appointment quickly because we already have your details
  • View & pay your invoices instantly
  • Set up & manage Direct Debits
  • View your statement of account

Recent Discussions

Microwave tripped candy oven now it won’t turn on
610 Hits 0 Votes 0 Replies
Posted on Saturday, 04 November 2023
Hi, I turned on the microwave this morning and it switched my oven off and now ...

Latest Replies

RE: beeping noise from hoover next washing machine
4 months ago
Quoted from Guest on Thursday, 02 May 2019 my hoover next washing machine has started beeping during a wash. still washes still spins and finishes load I have solved my beeping. Like...
RE: I have an error code C11 C21 C32 on my bosch oven HB13B251B
5 months ago
So had the issue with my oven this morning, for my type I needed to change c 5 0 to c 5 2 . Press and hold the clock for about 4 seconds to get in the the c code area - press the clock to move bet...